Oven Error Codes: What F1, F3, F10 and Others Mean
A fault code is a pointer, not a verdict. The same code can mean different things on different brands and model years, so treat the tables here as a starting point and confirm against the tech sheet for your model.

Updated October 2026 | How our content is written
Codes That Are Not Faults
| Display | Meaning | Clear it by |
|---|---|---|
| PF | Power was interrupted | Pressing Clear or Cancel, then setting the clock |
| LOC, Loc or a padlock | Control lock is on | Holding the lock key for about three seconds |
| Sab or SAb | Sabbath mode is active | Following the manual to exit the mode |
| Door or dr | Door is open or the latch is moving | Closing the door and waiting |
Common Fault Codes by Brand Family
| Brand family | Code | Usually points to |
|---|---|---|
| GE, Hotpoint | F2 | Oven temperature too high |
| GE, Hotpoint | F3 or F4 | Temperature sensor open or shorted |
| GE, Hotpoint | F7 | Stuck or shorted keypad |
| GE, Hotpoint | F9 | Door lock circuit |
| Frigidaire, Electrolux | F10 | Runaway temperature |
| Frigidaire, Electrolux | F11 | Shorted keypad |
| Frigidaire, Electrolux | F30 or F31 | Temperature sensor open or shorted |
| Whirlpool, Maytag, KitchenAid | F2-E1 | Keypad fault |
| Whirlpool, Maytag, KitchenAid | F3-E0 | Oven temperature sensor |
| Samsung | SE or -SE- | Shorted key on the touch panel |
| LG | F-9 | Oven not heating fast enough |
PF, F4 and brand fault codes
PF often means the oven lost power. Check the breaker and outlet, then reset the clock. F4 often points to a temperature sensor fault that needs testing. Westinghouse and AEG fault codes vary by model, so check the model number and the manual. If a code is not listed here, note the exact code and model number before calling.
The tech sheet is usually folded in an envelope behind the control panel, under the cooktop or behind the storage drawer. It lists every code for that exact model.
What to Try First
- Write the code down exactly, including any second part such as E0 or E1.
- Press Clear or Cancel and see if it returns right away or only when the oven heats.
- Cut power at the breaker for five minutes, then restore it.
- If the code is back within a day, the part it points to needs testing.
A code that returns only when the oven is hot often means a sensor or connector that fails with heat. A code that appears on a cold oven points more toward the keypad or the control.
When a Code Means Stop
Over-temperature and runaway codes, such as F2 on GE or F10 on Frigidaire, mean the oven may be heating without control. Turn it off at the breaker, not just at the panel, and do not use it until it has been checked. For a door that will not unlock, see the door repair page.
Common Questions
Can I keep using my oven with an error code?
If the code clears and stays away, yes. If it returns, or it is an over-temperature code, stop using the oven until it is diagnosed.
Does an error code always mean the control board is bad?
No. Most codes point to a sensor, keypad, lock or wiring. The board is the last thing to replace after those test good.
Where do I find my oven model number?
Look on the frame behind the oven door, on the side of the storage drawer opening, or behind the kick panel. It is on a metal or foil tag with the serial number.
What does F1 on a stove mean?
F1 usually means a problem with the oven’s electronic control board or touchpad. Unplug the oven for 5 minutes to reset it. If the display stays blank after power comes back, see oven won’t turn on. If F1 returns, the control board likely needs replacement by a technician.
What does F3 code on a stove mean?
F3 typically indicates a faulty oven temperature sensor. The sensor may be reading wrong temperatures. A technician can test it with a multimeter and replace it if needed.
How do I reset my oven error code?
Press Cancel or Off, then switch off the oven breaker or unplug the oven for about 5 minutes and turn it back on. A code caused by a power blip often clears this way. If the same code returns, stop using the oven and have the part behind that code tested.
Can foil on the oven floor cause an error code?
It can. Foil lining the oven floor traps and reflects heat, which can push the temperature sensor reading out of range and trigger a code or beeping. Remove the foil once the oven is cool and reset it. If foil has melted into the enamel or the code stays, the oven needs a closer look.
Why does my oven keep beeping?
A timer or cook time that has finished, a door left open, or a function that was started and not completed are the usual reasons. Press Cancel or Off. If the beeping comes with an error code, or keeps going with nothing set, it is a fault and the code tells the technician where to start.
Still Not Sure What Is Wrong?
Call and describe what you see. A two minute conversation often narrows it down.
