Electric Oven Repair in Ventura, CA
Electric ovens are simple machines with a few parts that do the heavy lifting. When one quits, a meter usually finds it in minutes. Here is what fails and how it is confirmed.

For electric oven repair Ventura homeowners can rely on, the technician tests the elements, sensor and power supply first.
Updated October 2026 | How our content is written

The 240 Volt Detail Most People Miss
An electric range runs on two 120 volt legs that add up to 240. Lose one leg, from a half-tripped double breaker or a burnt wire, and the clock, light and fan still work while the elements stay cold or barely warm. It looks like a dead element, but the oven is fine.
That is why a proper diagnosis starts at the terminal block on the back of the range. A scorched terminal block is one of the most common finds on ranges that have been pushed in and pulled out over the years.
Parts That Fail in Electric Ovens
| Part | What it does | How it is checked |
|---|---|---|
| Bake element | Main heat from the bottom, sometimes hidden under the oven floor | Continuity and a look for blisters or a break |
| Broil element | Top heat, also helps preheat on many models | Continuity |
| Temperature sensor | Tells the control how hot the cavity is | About 1,080 to 1,100 ohms at room temperature on most models |
| Thermal fuse or high limit | Cuts power if the oven overheats | Continuity |
| Control board relays | Switch the elements on and off | Voltage at the element while calling for heat |
When the Breaker Trips
An element that has split can touch the oven wall and short to ground. The breaker trips the moment the oven calls for heat. Leave the breaker off and do not keep resetting it, because each reset arcs at the break and can damage the wiring or the control.
In homes near the Ventura coast, corrosion on push-on connectors adds resistance and heat. A connector that has browned or gone brittle gets replaced along with the part it feeds.
Common Questions
Why does my oven work but the broiler does not?
Bake and broil are separate elements on separate relays. One can fail while the other works normally. A continuity test on the broil element answers it.
Is a hidden bake element harder to replace?
Yes. The oven floor or the back panel has to come out to reach it, so labor is higher than on an exposed element that unplugs from inside the cavity.
Can a bad sensor stop an electric oven from heating?
It can. If the sensor reads far out of range, the control refuses to heat or shuts down with a fault code to protect the oven.
What is the most common problem with an electric oven?
A burned out bake element is the most common reason an electric oven stops heating. You may see a break or blister on the element, or the oven heats only from the top. A faulty temperature sensor, a failed broil element and a tripped double breaker are the next things to check.
Book a Visit for Your Oven
Call with the brand, the model number and what the oven is doing, and ask what the technician found.
Electric ovens usually fail in simple ways. An element burns out, a sensor drifts, or a terminal overheats behind the back panel. We test each part with a meter instead of guessing, which keeps the repair to the one part that actually failed.
What Electric Oven Repair Costs in Ventura
Most electric oven repairs in Ventura run between $150 and $600 for parts and labor.
- Bake or broil element replacement: $175 to $350
- Temperature sensor replacement: $150 to $250
- Control board replacement: $225 to $600
- Thermal fuse replacement: $150 to $250
We test the failed part first and quote the full price before any work starts, so the number we give you is the number you pay.
Electric Oven Repair Across Ventura County
Electric ranges and single ovens are common in condos and apartments across Ventura, Oxnard and Camarillo. Most faults come down to a small group of parts: the bake element, the broil element, the temperature sensor, a relay on the control board or a tripped thermal fuse. Testing each one with a meter is what separates a $150 element swap from a control board job.
Common Electric Oven Repair Problems We Diagnose
- Bake or broil element stays dark
- Display works but the oven does not heat
- Oven trips the breaker
- Temperature runs far above or below the setting
- Visible blistering or a break in the element
Before the visit, check the breaker panel. Most electric ovens run on a double pole 240 volt breaker, and a half tripped breaker can light the display while the elements stay cold.
